Skip to content

Sales office and service Gdansk: +48 58 320 13 05   |  Sales office Warsaw: +48 504 060 713   |   PL  |  EN

Sales office and service Gdansk: +48 58 320 13 05   |  Sales office Warsaw: +48 504 060 713   |   PL  |  EN

Imer Machinery >> Imer Truck Mixers >> ORU LT 8.7H + SL version

Imer Truck Mixers ORU LT 8.7H + SL version

The ORU LT 8.7H concrete mixer with a nominal capacity of 8m3 and an 8×4 chassis is a good solution for areas with axle load limits. Low curb weight is a key factor, any weight reduction contributes to increased payload, lower fuel costs and tire replacement. A load capacity of up to 8 m3 of concrete can be achieved in combination with 3 and 4-axle low-weight vehicles. The perfect combination of lightness and long service life while maintaining ergonomics and safety for the operator. Concrete mixer body available in standard H version and light SL version (superlight).

In the standard version, the drum walls are made of abrasion-resistant 30MnB5 steel with a thickness of 4mm. The same steel is used for the mixing spirals. In the SL version, on the other hand, the walls are made of IMER WEAR Raex 300 steel with a thickness of 3mm and the spirals of IMER WEAR Raex 450. This has reduced the weight by more than half a tonne. The drum is rotated by a two-stage planetary gearbox, which is driven by a variable displacement hydraulic pump. Oil is cooled by a powerful radiator with a built-in reservoir. The body has a pressurised steel water tank with a capacity of 400 or 650l. The water system additionally has a water meter with a scale from 0 to 500 litres.

Concrete mixer bodies are standardly equipped with a rotating chute. Its working range is 180 degrees. However, its inclination angle is adjusted using a manual hydraulic lift. The manufacturer also supplies two lightweight extension gutters made of plastic. The drum has a manual lock to prevent rotation. After blocking the drum, the interior can be inspected through the inspection hatch located in the side wall. A foldable ladder with a platform is used to control the load. There is a hose for washing the machine at the base of the ladder. Steel surfaces are shot-peened in SA 2.5 grade. Then two layers of anti-corrosion paint are applied. The machine is driven by the power take-off from the truck engine.

Imer Truck Mixers ORU LT 8.7H + SL version

The ORU LT 8.7H concrete mixer with a nominal capacity of 8m3 and an 8×4 chassis is a good solution for areas with axle load limits. Low curb weight is a key factor, any weight reduction contributes to increased payload, lower fuel costs and tire replacement. A load capacity of up to 8 m3 of concrete can be achieved in combination with 3 and 4-axle low-weight vehicles. The perfect combination of lightness and long service life while maintaining ergonomics and safety for the operator. Concrete mixer body available in standard H version and light SL version (superlight).

In the standard version, the drum walls are made of abrasion-resistant 30MnB5 steel with a thickness of 4mm. The same steel is used for the mixing spirals. In the SL version, on the other hand, the walls are made of IMER WEAR Raex 300 steel with a thickness of 3mm and the spirals of IMER WEAR Raex 450. This has reduced the weight by more than half a tonne. The drum is rotated by a two-stage planetary gearbox, which is driven by a variable displacement hydraulic pump. Oil is cooled by a powerful radiator with a built-in reservoir. The body has a pressurised steel water tank with a capacity of 400 or 650l. The water system additionally has a water meter with a scale from 0 to 500 litres.

Concrete mixer bodies are standardly equipped with a rotating chute. Its working range is 180 degrees. However, its inclination angle is adjusted using a manual hydraulic lift. The manufacturer also supplies two lightweight extension gutters made of plastic. The drum has a manual lock to prevent rotation. After blocking the drum, the interior can be inspected through the inspection hatch located in the side wall. A foldable ladder with a platform is used to control the load. There is a hose for washing the machine at the base of the ladder. Steel surfaces are shot-peened in SA 2.5 grade. Then two layers of anti-corrosion paint are applied. The machine is driven by the power take-off from the truck engine.

Betonomieszarka IMER ORU LT 8.7H L

Technical data:

H version
Nominal capacity 8 m3
Geometric capacity 13,116 m3
Installation height 2735 mm
Min. installation length 6135 mm
Min. construction width 2300 mm
Drum speed 0-14 rpm
Unloading capacity 15 – 40 s/m3 depending on the consistency of concrete
Weight (empty) 3550 kg SL version 3032 kg
Chassis 6×4 – 8×4
Rolls: quantity 2 – diameter 280 mm

Betonomieszarka Imer ORULT 8.7H Szkic
Betonomieszarka IMER ORU LT 8.7H P

Standard equipment:

PMP two-stage planetary gearbox
Variable displacement hydraulic pump PMP
Oil cooler with integrated tank and filter, thermostat with electric fan

Mechanical (cable) speed control / direction of rotation of the concrete mixer
GAS+, GAS-, START, STOP motor control, safety switch on the back of the mixer
Auxiliary control on the back of the mixer: acoustic signal
Work lights – 4 pieces (2 pieces on the beam of the rear lights, 1 piece mounted under the platform, 1 piece on the platform-handrails – illuminating the hopper)
Reversing camera

180° rotating chute L=1500 mm with support and screw jack for angle adjustment
2 lightweight plastic (polystone) extension chutes with L=1000 brackets
Wear-resistant protective sheet on the main chute, hopper and rotary hopper
Rubber collar for inlet-hopper and V-discharge hopper
Telescopic ladder with platform and gate

650 l pressurised steel water tank
Pressurised water system
Water connection for filling the tank on both sides
Water meter 0-500 l
Washing hose at the base of the ladder and at the inspection platform

Single-axle polymer mudguards with mud flaps
Protection-cover between the frame beams
Standard rear bumper with steps on both sides for the operator

 

Betonomieszarka IMER ORU LT 8.7H L

Technical data:

H version
Nominal capacity 8 m3
Geometric capacity 13,116 m3
Installation height 2735 mm
Min. installation length 6135 mm
Min. construction width 2300 mm
Drum speed 0-14 rpm
Unloading capacity 15 – 40 s/m3 depending on the consistency of concrete
Weight (empty) 3550 kg SL version 3032 kg
Chassis 6×4 – 8×4
Rolls: quantity 2 – diameter 280 mm

Betonomieszarka Imer ORULT 8.7H Szkic
Betonomieszarka IMER ORU LT 8.7H P

Standard equipment:

PMP two-stage planetary gearbox
Variable displacement hydraulic pump PMP
Oil cooler with integrated tank and filter, thermostat with electric fan

Mechanical (cable) speed control / direction of rotation of the concrete mixer
GAS+, GAS-, START, STOP motor control, safety switch on the back of the mixer
Auxiliary control on the back of the mixer: acoustic signal
Work lights – 4 pieces (2 pieces on the beam of the rear lights, 1 piece mounted under the platform, 1 piece on the platform-handrails – illuminating the hopper)
Reversing camera

180° rotating chute L=1500 mm with support and screw jack for angle adjustment
2 lightweight plastic (polystone) extension chutes with L=1000 brackets
Wear-resistant protective sheet on the main chute, hopper and rotary hopper
Rubber collar for inlet-hopper and V-discharge hopper
Telescopic ladder with platform and gate

650 l pressurised steel water tank
Pressurised water system
Water connection for filling the tank on both sides
Water meter 0-500 l
Washing hose at the base of the ladder and at the inspection platform

Single-axle polymer mudguards with mud flaps
Protection-cover between the frame beams
Standard rear bumper with steps on both sides for the operator